Brake service at our Toronto shop starts with inspection and a vehicle-specific estimate. Pad/shoe thickness, rotor or drum condition, caliper operation, hoses, fluid and warning-light symptoms determine the work required. Ask for measured findings and a quote that identifies the axle, parts and labour.
Brake parts must match the VIN/application and brake package, including rotor diameter, thickness, offset, venting and the correct pad shape, hardware and wear sensors. OEM and aftermarket parts can differ in friction formulation, corrosion protection and warranty. Choose by application and documented specifications, not a universal claim that one pad material is always best.
Rotor minimum thickness and allowable runout/thickness variation are part- and vehicle-specific. Resurfacing is only an option when permitted and the finished rotor remains within specification. Electronic parking brakes may need service mode and calibration. Use the manufacturer’s specified brake fluid and service procedure.
Send year, make, model, trim, symptoms and whether the concern is front, rear or unknown. Confirm pad-only versus pad-and-rotor scope, hardware, calipers, fluid service, taxes and warranty in the written estimate. Grinding, fluid loss or impaired braking requires prompt professional assessment.
Related: suspension and steering and scheduled maintenance.
Visit 22 Ingram Drive, Unit 2, North York, Toronto, ON M6M 2L6. Call 647-809-9631 or request a quote on WhatsApp. Send your vehicle year, make, model and trim, tire size or symptoms, and preferred appointment time. Confirm stock, opening hours and appointment availability before travelling.
Why Masterdrive? Same‑day availability | Fair pricing | Technician‑level care
Pad/shoe thickness (mm), rotor/drum condition & runout, caliper slides/boots, hoses/lines, brake fluid test, parking brake check, ABS scan, and a road test—documented with clear recommendations.
Timing depends on the brake package, inspection findings, parts availability, corrosion and required electronic procedures. Confirm the appointment and expected completion time after assessment; same-day completion is not guaranteed.
Squealing or grinding, soft/low pedal, vibration when braking, longer stopping distances, burning smell, pulling to one side, or an ABS/brake warning light.
Measure thickness, variation and runout, and inspect condition against the exact vehicle/rotor limits. Replacement or permitted machining depends on those results and the applicable procedure. Confirm machining availability and the final quoted method; do not assume on-car resurfacing is available.
Choose the correct approved application and brake package first. Friction formulation, hardware, rotor compatibility and intended duty matter more than a universal ceramic-versus-metallic rule. Ask for the actual part number and whether it is OEM or a specified aftermarket equivalent.
Fresh pads need proper bed-in. Temporary noise can occur until transfer layer forms. We use quality shims, apply correct anti-squeal compounds, and provide bed-in guidance to keep things quiet.
Rotor thickness variation, runout, hub condition, wheel fastening or suspension faults may be involved. A symptom alone does not identify the defective part. Inspection and vehicle-specific measurements should support the repair recommendation.
Could be air in the system, old/contaminated brake fluid, leaking lines, a failing master cylinder, or a flexing hose. We pressure/visual test and bleed or repair as needed.
Follow the vehicle manufacturer's interval and fluid specification, supported by inspection and testing. Use the specified DOT classification and any additional OEM requirements. Do not substitute a different fluid solely because its DOT number is higher.
Confirm coverage for the exact vehicle and brake package before booking. The manufacturer may require a service mode, scan-tool procedure or calibration. Ask which operations and compatible parts are included; do not assume universal factory-tool coverage.
Absolutely. We scan for wheel-speed sensor, tone ring, hydraulic modulator, or wiring faults and provide a clear repair plan.
Yes—inspection, adjustment, hardware/spring kits, and shoe/drum replacement when worn or out of round.
Pulling, excessive heat, odour and uneven pad wear can indicate brake drag or another fault. Do not touch a hot wheel or continue driving with impaired braking; arrange safe assessment. Diagnosis determines whether slides, hardware, the hydraulic circuit or the caliper require work.
Contact Us or call 647-809-9631. Send the vehicle/trim, symptoms and any known brake package. Confirm inspection, compatible pad/rotor parts, labour, taxes and appointment availability.
Distinguish braking vibration from a steady-speed wheel or suspension concern. The inspection and quote should identify the actual brake package and the measured condition.
Have your vehicle, tire size or symptoms ready. Confirm the quote and appointment with the North York shop.
Call 647-809-9631 with your vehicle and braking symptoms. Prefer a message? Use the form below. Inspection findings determine the repair scope and estimate.